语言选择： 
China Lifute Sling Group manufacture UHMWPE Webbing Sling,Dyneema Webbing Sling,UHMWPE Lifting Sling,Lightweight UHMWPE Webbing Sling,UHMWPE Flat Sling.
China Lifute Sling Group manufactures lightweight UHMWPE webbing slings for lifting heavy loads where sling weight, bulk and edge damage are the limiting factors. The body is flat woven from ultra-high-molecular-weight polyethylene (UHMWPE / HMPE) yarn — the same fibre family sold under the Dyneema® and Spectra® brand names — and finished with an eye loop at each end. An equivalent UHMWPE sling weighs about 0.6 times a polyester sling, gives roughlytwice the tensile strength of polyester webbing of the same width, and resists cuts and abrasion far better. Every UHMWPE lifting sling is woven, stitched and proof loaded in our own factory in Taizhou, Jiangsu.
About 0.6x the weight of polyester. For the same working load limit a UHMWPE sling is roughly 40% lighter, so one rigger can carry and position a sling that would otherwise need two — which counts at height, in tanks and on scaffolding.
About 2x the tensile strength of polyester. The same capacity in a narrower, more flexible sling — or a much higher working load limit in the same webbing width.
Better cut and abrasion resistance. The woven UHMWPE body stands up to sharp edges, steel plate, scrap and rough concrete much better than polyester or nylon webbing.
Very low water absorption. UHMWPE does not take on water, does not stiffen and does not rot. Its density is below 1.0, so a dropped sling floats.
Excellent chemical and UV resistance. It holds up in salt water, oils and most acids and alkalis, indoors and outdoors, which is why it suits marine, port and offshore work.
Low elongation at working load. Less stored energy and less spring-back, so heavy and awkward lifts stay under control.
Soft and conformable. The flat woven body moulds itself to the load, so it grips well and leaves no hard spots or marring on finished and painted surfaces.
Thin and easy to stow. A narrow UHMWPE sling folds into a small package, which makes it easier to inspect, store and carry to the lift point.
| Property | UHMWPE / HMPE | Polyester (PES) | Nylon (PA) |
|---|---|---|---|
| Weight for the same WLL | About 0.6x polyester | Reference | Heavier than polyester |
| Tensile strength, same webbing width | About 2x polyester | Reference | Lower than polyester |
| Cut and abrasion resistance | Excellent | Good | Good |
| Elongation at working load | Low | Low to medium | High, absorbs shock |
| Water absorption | Very low, floats | Low | High, loses strength wet |
| UV and chemical resistance | Excellent | Very good | Good |
| Best used where | Weight, bulk and edge damage matter | General purpose lifting, best value | Shock loading and soft loads |
Eye to eye flat webbing sling — an eye loop at each end, the standard construction for this UHMWPE sling.
Endless loop (circular) flat webbing sling — a continuous loop with no ends, for vertical, choker and basket hitches.
Single layer or double layer flat woven UHMWPE webbing, woven in house on our own looms.
Reinforced and heat sealed wear points; optional PU / TPU coating for extra abrasion protection.
Protective sleeves in leather, PU or UHMWPE for sharp edges and corner protection.
White webbing as standard; other colours and printed customer logos on request.
Soft, pliable and low bulk, so the sling folds small and is easy to stow, carry and inspect.
| WLL | Webbing width (typical) | Effective length | Marking |
|---|---|---|---|
| 1 t | 25 mm | 1 m to 12 m | Printed WLL, length, material |
| 1.5 t | 30 mm | 1 m to 12 m | Printed WLL, length, material |
| 2 t | 35 mm | 1 m to 12 m | Printed WLL, length, material |
| 3 t | 45 mm | 1 m to 12 m | Printed WLL, length, material |
| 4 t | 50 mm | 1 m to 12 m | Printed WLL, length, material |
| 5 t | 60 mm | 1 m to 12 m | Printed WLL, length, material |
| 6 t | 75 mm | 1 m to 12 m | Printed WLL, length, material |
| 8 t | 90 mm | 1 m to 12 m | Printed WLL, length, material |
| 10 t | 100 mm | 1 m to 12 m | Printed WLL, length, material |
Working load limits above 10 t, intermediate capacities, special lengths and special webbing widths are made to order. Safety factor 7:1 to EN 1492-1 as standard — other ratios on request. Webbing widths above are typical references for UHMWPE flat webbing; confirm the exact width, thickness and mass per metre against our production drawing for your order.
Every sling is printed or labelled with the information needed for safe use and for an audit, following the marking requirements of EN 1492-1:
Working load limit in tonnes, and the effective length in metres.
Material — UHMWPE / HMPE.
Safety factor.
Standard complied with — EN 1492-1.
Manufacturer name, date of manufacture and a unique traceability number.
QR code or barcode traceability on request, linked to the test certificate.
Our sample sling carries the marking UHMWPE Webbing Sling / WLL 1.5 Ton / 2 M printed directly on the webbing. The exact wording, layout and language of the marking can be produced to your own specification.
Steel fabrication and steel plate handling — where cut resistance and low sling weight both matter.
Precast concrete and tunnel segments — strong, non marring and easy to place in tight shutters.
Wind energy — tower sections, nacelles and blades, including work at height where sling weight counts.
Shipyards, ports and offshore — wet, salty and abrasive environments where polyester ages faster.
Heavy machinery, dies and moulds — precise, low stretch lifts with little spring-back.
Rail and locomotive maintenance — lifting bogies, wheelsets and structural assemblies.
Glass, stone and finished surfaces — a soft woven body that will not scratch the load.
Power stations and plant maintenance — where a light sling can be carried to the lift point by hand.
We manufacture to your drawing as well as to our own standard range, and we have been producing OEM and ODM lifting slings for overseas customers for decades.
Working load limit, webbing width, thickness and effective length made to your specification.
Eye to eye or endless loop construction; single or double layer webbing; reinforced or coated wear points.
Protective sleeves, corner protectors and wear pads for abrasive or sharp loads.
Your own colour, printed logo, label layout and customer part number on the sling.
Test certificate, proof load report and batch traceability with every shipment.
China Lifute Sling Group has been manufacturing textile lifting and lashing equipment for46 years. All weaving, stitching, splicing, printing and testing are carried out inside our own 10,000 m² factory in Taizhou, Jiangsu Province, so quality control stays in our hands from raw yarn to the finished sling. We run more than 100 machines and a workforce of 86 production operators, with a daily output of over 7 tons of finished product.
UHMWPE webbing is checked for width and thickness, weave density, stitch pattern and marking content, and every finished sling is proof loaded before packing. Minimum breaking load is verified on the test bed and recorded against the sling’s traceability number, so the certificate that ships with the sling can always be traced back to the batch and the test record. Our products are covered by ISO, CE, DNV and PICC certification.
Read more about our factory and capability.
It is a flat woven lifting sling made from ultra-high-molecular-weight polyethylene (UHMWPE, also called HMPE) yarn — the same fibre family sold under the Dyneema® and Spectra® brand names. We weave it into flat webbing and finish it with an eye loop at each end, so the sling can be used in vertical, choker and basket hitches.
About 0.6 times the weight, so roughly 40% lighter for the same working load limit. One operator can carry and position a UHMWPE sling that would normally need two people, which makes a real difference at height or in confined spaces.
Approximately twice the tensile strength for the same webbing width. That gives the same capacity in a narrower and more flexible sling, or a much higher working load limit in the same width — which is why a UHMWPE lifting sling can often replace a much wider and heavier polyester sling on the same job.
Yes — noticeably better than polyester or nylon, which is why they are used on steel plate, structural steel, scrap and precast concrete. For very sharp edges we can add a protective sleeve.
Standard capacities from 1 t to 10 t, plus higher capacities, intermediate sizes and custom lengths and widths to order. Our sample sling is marked WLL 1.5 ton × 2 m. Send us the working load limit, effective length and hitch type and we will confirm the webbing width and the marking.
UHMWPE has very low water absorption and a density below 1.0, so it does not take on water and it floats. It does not stiffen, swell or rot when wet, which suits wet, marine and offshore work.
Normally about -40 °C to +80 °C. Keep it clear of hot surfaces, weld spatter and open flame, and use a heat resistant aramid sling where high temperature cannot be avoided.
Inspect the sling before every lift: look for cuts, abrasion, pulled or broken yarns, chemical damage, heat damage and a missing or illegible marking.
Protect the sling from sharp edges with a sleeve or corner protector, and never drag a load over the sling.
Do not exceed the working load limit, and remember that capacity falls in choker and multi-leg configurations.
Store clean and dry, out of direct sunlight, away from heat sources and chemicals.
Wash only with clean water and a mild detergent; never machine wash or tumble dry.
Retire the sling immediately if the marking label is missing, if the webbing is cut or badly abraded, or after an overload or shock load.
Keep a written inspection record — see our article on webbing sling WLL and mode factor for how capacity changes with hitch type.
Tell us the working load limit, effective length, hitch type and the environment the sling will work in, and we will come back with the right webbing width, sling weight and a factory direct price. Custom lengths, printed logos, OEM labels and test certificates are all part of the service.
Order online or send an enquiry through our contact page, call +86 133 6520 3036, or email cnlift@126.com.
Company：China Lifute Sling Group
Contact：Mss Wang
Tel：+8613365203036
Mobile：+8613365203036
E-mail：cnlift@126.com
Address：TaiZhou City, JiangSu Province, Lifute District ,China
